Rees Environmental Monitoring System

Scaling(m) parameter:

Offset(b) parameter:

System Reading

Rees System Reading When Independent Standard Was Read:

Reading of Independent Standard at the Same Time:

System Reading = (Input Volts X m) + b

Inhibit or Enable an Input

Node Name:
Input Name:

	Inhibit for 15 Minutes
	Inhibit for:hours
	Reset and Enable

User Name:
Password:

Calibrate a Sensor

Node Name:
Input Name:

Sensor Currently Reads:		Deg C
One Person Calibration

If you leave the One Person Calibration Box unchecked, then the Centron will use the current system reading for the as-found.

If you check the One Person Calibration box, then this data entry may take place at a time other than the time when calibration was tested. If so, the offset calculated will be identical regardless of the time of data entry. However, it is essential that the reference and the Rees system are read at the same time and the data noted for entry into the boxe(s) below.

Reading of Independent Standard:

Operator:
Reference Equipment for Line 1:
Line 1 Equipment Cal Date:
Reference Equipment for Line 2:
Line 2 Equipment Cal Date:
Reference Equipment for Line 3:
Line 3 Equipment Cal Date:
Procedure Number:
Sensor Tolerance:
Calibration Uncertainty:
Calibration Date:
Calibration Due Date:
Asset:
Ambient Conditions:
Certificate Comment:

Comment

Calibrate a Sensor

Node Name:
Input Name:

Sensor Currently Reads:		Deg C
Uncalibrated Reading Would Be:		Deg. C

This data entry may take place at a a time other than the time when calibration was tested. If so, the offset calculated will be identical regardless of the time of data entry. However, it is essential that the NIST meter and the Rees system are read at the same time and the data noted for entry into the boxes below.

Rees System Reading When Independent Standard Was Read:
Reading of Independent Standard at the Same Time:

NOTE: This calibration method will not generate ISO17025 calibration certificates.

Comment

Calibrate a Linear Transducer

Node Name:
Input Name:

This data entry may take place at a a time other than the time when calibration was tested.If so, the offset calculated will be identical regardless of the time data entry. However, it is essential that the NIST meter and the Rees system are read at the same time and the data noted for entry into the boxes below.

NOTE: This calibration method will not generate ISO17025 calibration certificates.

Comment

Please enter a Comment

User:

Password:

Please Select a Node to Open

Trouble Alarm

Alarm Sound:
Alarm Delay (mins):
Department Monitored:
Phone:
Phone List:
Email:
Location:

Input Name:
Reads:
Type:
Input/Grp:
Inhibit for (mins):
Scaling (m) Parameter:
Offset (b) Parameter:
Units:
Map Icon:

Alarm

Alarm Limits:	to
Alarm Sound:
Alarm Delay (mins):
Persistance:
Alarm Schedule:
Alarm Checklist:

Phone

Telephone Alarm:		Delay: Mins.
Day/Night Schedule:
Day Phone List:
Night Phone List:

Email

Send Emails for:

Alarm Events
Return To Normal Events
Alarm Inhibit Events

Send All Emails To:
After 15 minutes, send to:
After 30 minutes, send to:

Pre-Alarm Alert

Alerts:	Sound Pre-Alarm Alert
Alert Limits:	to
Alert Delay (mins):

Advanced

Logging for Advanced Reports:
Comment Required for this Input:

Node's Alarm Relay:
Input's Spoken ID:
Telephone Calling Priority:

Please Select a List to Program

Add or Change Name

Edit or Select from Phone Directory

Add a Phone Number

Name:
Number:

Add/Edit Alarm Handling Instruction Lists

List:

NOTE: The text that you enter above will be inserted into all comments about alarms that use these instructions. You may put square brackets [] into the notes to allow the person responding to the alarm to enter a response.

Edit System Access Codes

User:

Login:

Valid in this Node
Code is locked out

Department:

Permissions:

Enable Alarms
Inhibit Single Alarms for up to: Min.
Inhibit Single Alarms for a Long Time
Inhibit Multiple Alarms for a Long Time
Program the Card Access System
Program Environmental System Inputs
Program Environmental System Outputs
Calibrate Inputs
Electronic Data Reviews and Approvals
Program Node Phone Lists
Program Master Phone Lists
Reset Passwords for Non-Admin Accounts
Modify Security Codes and Permissions

Add / Change a User

Name:
Login:
Password:	Don't Change
Phone PIN:

Add / Change a Password

Password:
Confirm:

Add / Edit Departments

Dept:

Advanced Options

Institution:
Address:
Address:
Normal Logging Rate:
In-Alarm Logging Rate:
Bobble Logging:	Log In-Range/Out-of-Range During Alarms
Bobble Logging:	Log Pending/Normal Transitions
Login Timeout:	Minutes
Passwords Expire:	After Days
Minimum Password Length/Complexity:	Characters Enforce Complexity
Electronic Signatures (21CFR11):	Require for Program/Alarm Changes
Account Lockout:	Accounts will Lock after 5 Failed Logins
Comments:	Comment Expected to Explain User Actions
Date Format:	European 1-Jan-Year 4 Digit Year
Time Format:	Use 24 Hour Clock

Dates:
Y-Axis:

Dates:

Please Enter Dates

Starting Date:
Ending Date:

Please Enter Selections

Starting Date:
Ending Date:
	Select by Event Type
	Select by Input Name
	Select by Input Number

Readings Reports

Starting Date:		Time:
Ending Date:		Time:

Edit Schedules

Schedule

On at: